Close

Amendment

Products

Document #:
Revision
E
Product Type
Released:  04/20/2022
Language
English
Current Revision
IPC-6012E-AM1 is an Amendent to the IPC-6012E that clarifes the distinction between receding and dewetting solder in reflowed SPb or HASL coatings. The Amendment also provides amended criteria for minimum external conductor thickness of the finished printed board and new acceptance criteria for the minimum thickness of internal plated layers
Document #:
Revision
C
Product Type
Released:  11/02/2017
Language
English
Current Revision
The J-STD-006C-AM1 amendment provides better detail of a solder alloy's maximum allowed deviation about the nominal level of the element's mass than was provided in past alloy standards. The J-STD-006C-AM1 amendment provides information on negative effects of adding rare earth elements to specific, heavy tin-containing, lead-free solder alloys and propensity of tin whisker formation. Finally, the...

IPC-1755 - Revision A - Amendment 1

Responsible Sourcing of Minerals Data Exchange Standard

Document #:
Revision
A
Product Type
Released:  10/27/2021
Language
English
Current Revision
IPC-1755A-Am1 cannot be used without a copy of IPC-1755A the base standard. You can purchase IPC-1755A-Am1 and IPC-1755A in the IPC.org online store. The IPC-1755A standard establishes the requirements for exchanging data between suppliers and their customers regarding the responsible resourcing of minerals. The IPC-1755 standard originally addressed conflict minerals within the scope of the Dodd...
Document #:
Revision
Original Version
Product Type
Released:  09/01/2013
Language
English
Current Revision
Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards Amendment 2 to IPC-4552 is a new section in the original release of the IPC-4552. The Amendment 2 provides the “rules” by which any rework and/or repair of a printed board's ENIG surface finish is allowed. Effective September 2012.

IPC-J-STD-001 - Revision F - Amendment 1

Requirements for Soldered Electrical and Electronic Assemblies

Document #:
Revision
F
Product Type
Released:  11/01/2015
Language
English
This is an amendment to IPC J-STD-001F, a recognized industry-consensus standard covering materials and processes. Changes include, but are not limited to, a revision to plated-through hole, PTH, minimum fill requirements and BGA voiding criteria, new graphics for several surface mount component types, revised staking criteria, and recognition of the paragraphs addressed in J-STD-001FS, Space...
Document #:
Revision
D
Product Type
Released:  09/01/2017
Language
English
The IPC-6012D-AM1 makes changes to the existing acceptance criteria for copper wrap plating measurements as defined by IPC-6012D. The IPC-6012D-AM1 implements a dual criterion for Class 3 copper wrap plating, based on design effectivity (before and after January 01, 2018), so as not to impose onto legacy designs any additional qualification activity associated with adopting acceptance requirements...
Document #:
Revision
Original Version
Product Type
Released:  05/01/2018
Language
English
Current Revision
IPC/JEDEC-9707-AM1 is an amendment which clarifies that the standard is only applicable to transient bending during short-term test operations. The standard specifies a common method of establishing strain limits of board-level device interconnects under spherical transient bending conditions, the worst-case flexure condition that can occur during conventional printed board/system assembly...
Document #:
Revision
Original Version
Product Type
Released:  05/01/2006
Language
English
Current Revision
IPC-4821 Amendment 1 provides the update of IPC-CF-148 to the correct IPC-4563, references the IPC-TM-650, Method 2.5.7.2 for correct Hi-Pot testing of these thin materials, uses proper reference for visual inspection by inspectors and finally, updated the first five material specification sheets (IPC-4821/1 through IPC-4821/5) that now show Effective Dates of April 2010. The Specification Sheet...