Products
IPC/WHMA-A-620E is the only industry-consensus standard for Requirements and Acceptance of Cable and Wire Harness Assemblies. IPC/WHMA-A-620E describes materials, methods, tests and acceptance criteria for producing crimped, mechanically secured and soldered interconnections and the related assembly activities associated with cable and harness assemblies. IPC/WHMA-A-620E was developed by IPC and...
The IPC-7711/21 guide provides procedures for rework, repair and modification of printed board assemblies, including tools and materials, common procedures, coating removal and graphics to assist the user.
Amendment 1 to IPC-7711/21C, the document provides procedures for removal and installation of D-Pak components
IPC/WHMA-A-620E-S space addendum provides additional requirements to IPC/WHMA-A-620E standard to ensure the reliability of cable and wire harness assemblies that must survive the vibration and thermal excursions encountered getting to and operating in the military and space environments. IPC/WHMA-A-620E-S cannot be used as a standalone document. It must be used with the base standard IPC/WHMA-A...
IPC/WHMA-A-620C-R rail transit addendum provides additional requirements to IPC/WHMA-A-620C standard, describing materials, methods, tests, and acceptance criteria for producing crimped, mechanically secured, and soldered interconnections. It also provides the related assembly activities associated with cable and harness assemblies in rail transit industry, to ensure the high reliability and...
Contains over 150 industry approved test techniques and procedures for chemical, mechanical, electrical, and environmental tests on all forms of printed boards and connectors. New and updated test methods are available for download at https://www.ipc.org/test-methods .
These tables are from IPC/WHMA-A-620 Revision B Chapter 19 Testing. They are provided in an electronic format that permits users to edit the tables to add user-specific criteria. These files are authorized for copying/reproduction.
IPC/WHMA-A-620D is the only industry-consensus standard for Requirements and Acceptance of Cable and Wire Harness Assemblies. IPC/WHMA-A-620D describes materials, methods, tests and acceptance criteria for producing crimped, mechanically secured and soldered interconnections and the related assembly activities associated with cable and harness assemblies. IPC/WHMA-A-620D was developed by IPC and...
IPC/WHMA-A-620E-RL is a redline document showing the difference from IPC/WHMA-A-620D to IPC/WHMA-A-620E. IPC/WHMA-A-620E-RL provides a side-by-side comparison of the two documents and includes the figures and tables. The document shows deleted/changed text in the IPC/WHMA-A-620D pages and new/revised text in the IPC/WHMA-A-620E pages. Due to the complexity of this document, it is only available in...
This standard is the first of its kind for IPC; the first acceptability standard for electronic enclosures. It contains acceptability criteria that pertain to the "box build" of the assembly process. This standard has been written to direct manufacturers and end users of electronic enclosures of electrical and electronic equipment to understand the best practices to meet requirements, ensuring the...
IPC-9191 reflects the principals of statistical process control (SPC) represented by ISO/DIS 11462-1, Guidelines for Implementation of Statistical Process Control (SPC) -- Part 1: Elements of SPC. This document outlines the SPC philosophy, implementation strategies, tools, and techniques used for relating process control and capability to final product requirements. Supersedes IPC-PC-90.
This redline provides a side-by-side comparison the changes from Revision C to Revision D of IPC-7711/21.
This guideline standard is intended to aid in interpretation of the requirements in IPC-9191, "General Guidelines for Implementation of Statistical process Control," specifically for printed board assembly (PBA) manufacture. This document and IPC-9191 should be used together; the standards are cross-referenced to each other in the Appendices of this guideline. This standard promotes process...
This document is a tool for a customer or supplier organization's internal audit group to assess a statistical process control (SPC) system against the requirements of IPC-9191. This document should be used by customers and suppliers of any size and for any commodity. This tool can be used to perform an assessment of the use of SPC at both organizational and process levels. The questions in this...
Tackling PCB cleanliness is a tough job; residues on printed circuit boards are directly related to the reliability of the produced hardware and can result in serious failures if not known or monitored. But how do you measure "cleanliness"? How clean is "clean"? The IPC-5701 provides guidance into how these issues should be approached and specified in purchasing documents, addressing levels of...
This guide provides procedures for rework, repair and modification of printed board assemblies. Included in this revision are the procedures previously released as change pages, an updated general information and common procedures section, new procedures for BGAs using focused IR Reflow Systems with integral preheater and general updates to all other procedures.
This is the only industry-consensus standard for Requirements and Acceptance of Cable and Wire Harness Assemblies, and it includes new sections for safety wiring, safety cable, grommets, and raceways along with updated information across many of the sections. With over 700 photographs and illustrations, this standard describes materials, methods, tests and acceptance criteria for producing crimped...
Amendment 1 to IPC/WHMA-A-620B This amendment provides resolution to some internal conflicts, aligns common criteria to other IPC standards, and corrects some editorial errors. This amendment is only to be used in conjunction with IPC/WHMA-A-620 Revision B, October 2012. Follow your company policy and procedures to make pen and ink changes or notations to the published IPC/WHMA-A-620 Revision B...
This guide includes everything needed for repair and rework of electronic assemblies and printed circuit boards. IPC-7711B/7721B Rework, Modification and Repair of Electronic Assemblies has received a complete procedure by procedure update to assure applicability to both lead free and traditional SnPb soldered assemblies. This single volume includes all previously published changes and several new...
IPC/WHMA-A-620E 是线缆及线束组件的要求与验收的唯一行业共识标准。本标准描述了用于压接、机械紧固或焊接互连的材料、方法、测试和可接受性标准以及其他线缆线束组件组装活动的相关标准。 IPC/WHMA-A-620E由IPC和线束制造商协会(WHMA)(隶属于IPC)共同开发。
IPC/WHMA-A-620D ist die einzige, im Branchenkonsens entwickelte Richtlinie für Anforderungen und Abnahmekriterien für Kabel- und Kabelbaum-Baugruppen. IPC/WHMA-A-620D beschreibt Materialien, Methoden, Tests und Abnahmekriterien für die Herstellung gecrimpter, mechanisch gesicherter oder gelöteter Verbindungen und die zu den Kabel- und Kabelbaum-Baugruppen zugehörigen Montageaktivitäten. IPC/WHMA-A...
Space Applications Electronic Hardware Addendum to IPC/WHMA-A-620A. When specifically required by procurement documentation, this Addendum supplements or replaces specifically identified requirements of IPC/WHMA-A-620, Revision A.
El IPC/WHMA-A-620D es el único estándar consensuado por el sector sobre Requisitos y aceptabilidad de ensambles de cables y mazos de cables. El estándar IPC/WHMA-A-620D describe los materiales, métodos, pruebas y criterios de aceptabilidad para la producción de interconexiones crimpadas, mecánicamente aseguradas o soldadas y las actividades de ensamble relacionadas que estén asociadas con...
IPC/WHMA-A-620D er den eneste industriudviklede standard for ” Godkendelseskrav for kabler og for produkter med wire harness”. IPC/WHMA-A-620D beskriver materialer, metoder, test og godkendelseskriterier for fremstilling af crimpede samlinger, mekanisk sikrede og loddede forbindelser samt de tilhørende monteringsprocesser som er forbundet med kabel og harness produkter. IPC/WHMA-A-620D blev...
IPC/WHMA-A-620D est la seule norme consensuelle de l’industrie pour les exigences et l’acceptation des assemblages de câbles et de faisceaux de fils. IPC/WHMA-A-620D décrit les matériaux, les méthodes, les tests et les critères d’acceptation pour la production d’ensembles interconnectés brasés, sertis et mécaniquement sécurisés, ainsi que les activités d’assemblage qui y sont associées pour...
Coming Soon
IPC-7095E: Design and Assembly Process Implementation for Ball Grid Arrays (BGAs)
IPC-2294: Design Standard for Printed Electronics on Rigid Substrates
IPC-6904: Qualification and Performance Specifications for Printed Electronics on Rigid Substrates
J-STD-005B: Requirements for Soldering Pastes
IPC-4105: Specification for Metal Base Copper Clad laminates for Rigid Printed Boards
J-STD-004D: Requirements for Soldering Fluxes
IPC-4413: Specification for Finished Fabric Woven from Low Dk Glass for Printed Boards