Products
This popular document covers land pattern design for all types of passive and active components, including resistors, capacitors, MELFs, SOPs, QFPs, BGAs, QFNs and SONs. The standard provides printed board designers with an intelligent land pattern naming convention, zero component rotations for CAD systems and three separate land pattern geometries for each component that allow the user to select...
The IPC J-STD-004C WAM1 standard prescribes general requirements for the classification and characterization of fluxes for high quality solder interconnections. The IPC J-STD-004C WAM1 standard may be used for quality control and procurement purposes. Soldering flux materials include the following: liquid flux, paste flux, solder paste, solder cream as well as flux-coated and flux-cored solder...
The IPC-A-640A standard provides acceptance requirements and technical insight that have been removed from acceptance standards for cable and wire harness assemblies incorporating optical fiber, optical cable and hybrid wiring technology. The IPC-A-640A is intended for use by the design engineer, manufacturing engineer, quality engineer and other individuals responsible for tailoring specific...
The IPC-CC-830C standard establishes qualification and conformance requirements for electrical insulating compounds (conformal coatings). It has been designed and constructed with the intent of obtaining maximum confidence in the materials with minimum test redundancy. The IPC-CC-830C standard covers: • The qualification and qualification retention of the conformal coating material (Table 3-1...
IPC-9252 defines levels of appropriate testing and assists in the selection of the test analyzer, test parameters, test data and fixturing required to perform electrical test(s) on unpopulated printed boards and innerlayers. Revision B provides new requirements for resistive and indirect continuity and isolating testing, test record marking and traceability and an updated sample electrical test...
The IPC-7801A standard provides requirements for process control of conveyorized solder reflow ovens. It includes a methodology for performing temperature measurements over time to establish a baseline profile, and then provides requirements to verify repeatability through periodic verification of the oven profile.
Provides requirements for dielectric adhesives to hold components in place from the mounting to the soldering process and identifies test methods to ensure their long term properties. 9 pages. Released December 2014.
IPC-7526A handbook addresses understencil cleanliness during stencil printing, removal of solder paste from stencils following the cleaning process and misprint PCB board cleaning considerations.
The IPC-9701B standard establishes a thermal cycling test method to characterize the fatigue lifetimes of surface mount solder attachments of electronic assemblies. The surface mount devices may be solder-attached to rigid, flexible or rigid-flex printed boards. The characterization results can be used to predict the field lifetime of solder attachments for the use environments and conditions of...
This guideline describes flexibility and stretchability testing to evaluate printable electronics for stretchable and wearable applications. 26 pages. Released March 2017
While there are a variety of industry test vehicles for the examination of material compatibility, the IPC-B-52 test board was created to meet the needs for testing both ion chromatograph and surface insulation resistance (SIR) which would be more representative of the manufacturing materials and processes. IPC-9203A standard addresses the IPC-B-52 test vehicle, which can be used to evaluate a...
Strain gage testing allows for objective analysis of the strain and strain rate levels to which a surface mount package may be subjected to during assembly, test and operation. Excessive strain can result in various failure modes for different solder alloys, package types, surface finishes or laminate materials. This document describes specific guidelines for strain gage testing during the printed...
This specification establishes the certification requirements for facilities that inspect/test printed boards, components and materials. This specification is intended to provide a minimum standardized basis for evaluating or auditing a technically oriented inspection/testing facility. Revised November 1997. 15 pages.
This document standardizes the requirements for power conversion devices (PCDs) for the computer and telecommunications industries. The phrase “power conversion devices” refers to ac to dc and dc to dc modules, converters and power supplies. This specification sets the requirements for design; qualification testing; conformance testing and manufacturing quality/reliability processes, but does not...
IPC-7094A describes the design and assembly challenges for implementing flip chip technology in a direct chip attach (DCA) assembly. The effect of bare-die or die-size components in a flip chip format has an impact on component characteristics and dictates the appropriate assembly methodology. The IPC-7094A standard focuses on design, assembly methodology, critical inspection, repair and...
This document describes the design and assembly challenges and ways to address those challenges for implementing 3D component technology. Recognizing the effects of combining multiple uncased semiconductor die elements in a single-package format can impact individual component characteristics and can dictate suitable assembly methodology. The information contained in this standard focuses on...
IPC-2231A provides guidelines for establishing a best practice methodology for use in developing a formal DFX (Design for Manufacturing, Fabrication, Assembly, Testability, Cost, Reliability, Environment, Reuse) process for layout of printed boards.
This document is the product of the IPC Electrochemical Migration (ECM) Task Group. It was drafted to provide guidance regarding implementation of the User Guide for the IPC-TM-650, Method 2.6.25, Conductive Anodic Filament (CAF) Resistance and Other Internal Electrochemical Migration Testing to evaluate the effects of mechanical stress, laminate material fracturing, ionic contamination, moisture...
The IPC-6017A standard defines the electrical, mechanical, and environmental requirements specific to embedded passive and active circuitry in printed boards. These requirements are in addition to the applicable requirements of other performance specification(s) (e.g., J-STD-001).
The IPC-9202A, Material and Process Characterization/Qualification Test Protocol that records changes in Surface Insulation Resistance (SIR) on a representative sample of a printed circuit assembly (PCA). It quantifies any deleterious effects that might arise from solder flux or other process residues left on external surfaces after soldering, which can cause unwanted electro-chemical reactions...
The IPC-1401A standard specifies the requirements and best practice guidelines for an effective corporate social responsibility (CSR) management system to help an enterprise integrate CSR as a customer requirement into products and value chain activities, as well as to identify and manage CSR risks and opportunities through cooperation with customers and suppliers, to enhance the competitive...
The IPC-6903A standard provides 62 additional terms and definitions for the design and manufacture of printed electronics. The IPC-6903A standard creates a common language and understanding for the worldwide printed electronics community.
Developed by the OEM council of the IPC, IPC-1720A categorizes electronic assembly manufacturer capabilities and supplies the OEM customer with detailed, substantive information. This program simplifies auditing processes and reduces the frequency of audits, thereby decreasing paperwork and improving efficiency. Company and Site Description, Site Capability Snap Shot, Equipment Profile (Pre-site...
Now updated to align with IPC-7912A for end item DPMO, this document defines consistent methodologies for computation of in-process defects per million opportunities (DPMO) metrics for any evaluation stage in the assembly process. It is intended for use in measuring in-process assembly steps rather than end product determination. Calculation of completed item DPMO is addressed in IPC-7912A. A...
Surface Insulation Resistance (SIR) testing is a tool used not only for characterization testing of production processes such as solder masks, soldering flux, and conformal coatings, but also for examining the electrochemical reactions at each stage of the electronic assembly production process. This handbook covers the terminology, theories, test procedures and test vehicles of SIR testing...
Coming Soon
IPC-7095E: Design and Assembly Process Implementation for Ball Grid Arrays (BGAs)
IPC-7530B: Guidelines for Temperature Profiling for Mass Soldering Processes (Reflow & Wave)
IPC-2294: Design Standard for Printed Electronics on Rigid Substrates
IPC-6904: Qualification and Performance Specifications for Printed Electronics on Rigid Substrates
IPC-4105: Specification for Metal Base Copper Clad laminates for Rigid Printed Boards