Menu
Close
Contact IPC

Amendment

Your results

Document #

Language

Products

IPC-6012E-AM1 Cover Image

IPC-6012 - Revision E - Amendment 1

Qualification and Performance Specification for Rigid Printed Boards

Document #:
IPC-6012
Revision
E
Product Type
Amendment
Released:  04/20/2022
Language
English
Current Revision
IPC-6012E-AM1 is an Amendent to the IPC-6012E that clarifes the distinction between receding and dewetting solder in reflowed SPb or HASL coatings. The Amendment also provides amended criteria for minimum external conductor thickness of the finished printed board and new acceptance criteria for the minimum thickness of internal plated layers
no-image-available

IPC-4554 - Amendment 1

Specification for Immersion Tin Plating for Printed Circuit Boards

Document #:
IPC-4554
Revision
Original Version
Product Type
Amendment
Released:  09/01/2013
Language
English
Current Revision
IPC-4554, "Specification for Immersion Tin Plating for Printed Circuit Boards," is the third document in a series of specifications [the first two are: IPC-4552 which addresses electroless nickel/immersion gold (ENIG) and IPC-4553 which addresses immersion silver (IAg)] that set the requirements for printed circuit board surface finishes that are alternates to eutectic tin-lead. IPC-4554, a full...
no-image-available

IPC-6013 - Revision D - Amendment 1

Qualification and Performance Specification for Flexible and Rigid-Flexible Printed Boards

Document #:
IPC-6013
Revision
D
Product Type
Amendment
Released:  05/03/2018
Language
English
IPC-6013D-AM1 is an amendment makes changes to the existing acceptance criteria for copper wrap plating measurements as defined by IPC-6013D. IPC-6013D-AM1 is an amendment which implements a dual criterion for Class 3 copper wrap plating, based on design effectivity (before and after July 01, 2018), so as not to impose onto legacy designs any additional qualification activity associated with...
no-image-available

IPC-9707 - Amendment 1

Spherical Bend Test Method for Characterization of Board Level Interconnects

Document #:
IPC/JEDEC-9707
Revision
Original Version
Product Type
Amendment
Released:  05/01/2018
Language
English
Current Revision
IPC/JEDEC-9707-AM1 is an amendment which clarifies that the standard is only applicable to transient bending during short-term test operations. The standard specifies a common method of establishing strain limits of board-level device interconnects under spherical transient bending conditions, the worst-case flexure condition that can occur during conventional printed board/system assembly...
no-image-available

IPC-6012 - Revision D - Amendment 1

Qualification and Performance Specification for Rigid Printed Boards

Document #:
IPC-6012
Revision
D
Product Type
Amendment
Released:  09/01/2017
Language
English
The IPC-6012D-AM1 makes changes to the existing acceptance criteria for copper wrap plating measurements as defined by IPC-6012D. The IPC-6012D-AM1 implements a dual criterion for Class 3 copper wrap plating, based on design effectivity (before and after January 01, 2018), so as not to impose onto legacy designs any additional qualification activity associated with adopting acceptance requirements...
no-image-available

IPC-A-610 - Revision F - Amendment 1

Acceptability of Electronic Assemblies

Document #:
IPC-A-610
Revision
F
Product Type
Amendment
Released:  12/14/2015
Language
English
This amendment cannot be used without a copy of IPC-A-610F. See Related items. This is an amendment to IPC-A-610F, a recognized industry-consensus standard covering acceptability requirements for electronic assemblies. Changes include, but are not limited to, a revision to plated-through hole, PTH, minimum fill requirements, BGA voiding criteria for noncollapsing balls, and staking criteria.
no-image-available

IPC/WHMA-A-620 - Revision B - Amendment 1

Requirements and Acceptance for Cable and Wire Harness Assemblies

Document #:
IPC/WHMA-A-620
Revision
B
Product Type
Amendment
Released:  08/01/2013
Language
English
This amendment provides resolution to some internal conflicts, aligns common criteria to other IPC standards, and corrects some editorial errors. This amendment is only to be used in conjunction with IPC/WHMA-A-620 Revision B, October 2012. Follow your company policy and procedures to make pen and ink changes or notations to the published IPC/WHMA-A-620 Revision B. When there are changes to a...

IPC-6012 - Revision E - Amendment 1

刚性印制板的鉴定及性能规范- 修订本1

Document #:
IPC-6012
Revision
E
Product Type
Amendment
Released:  10/28/2022
Language
Chinese
Current Revision
IPC-6012E-AM1是IPC-6012E的修订本，澄清了再流焊SnPb或HASL镀层中退润湿和焊料回缩之间的区别。 该修订本还为成品印制板的最小外部导体厚度提供了修订标准，并为内部电镀层的最小厚度提供了新的接受标准。
no-image-available

IPC-6012 - Revision D - Amendment 1

Sert Baskı Devre Kartları İçin Kalifikasyon ve Performans Spesifikasyonu

Document #:
IPC-6012
Revision
D
Product Type
Amendment
Released:  01/25/2019
Language
Turkish
Current Revision
Bu döküman; kaplı delikiçine sahip olan veya olmayan tek yüzlü, çift yüzlü baskı devre kartları ve kör/gömülü geçiş deliklerine sahip olan veya olmayan çok katmanlı baskı devre kartları ile metal çekirdekli kartları içeren sert baskı devre kartlarının kalifikasyonunu ve performansını kapsamaktadır. Son kaplama ve yüzey kaplama gereklilikleri, iletkenler, delikler/geçiş delikleri, kabul testlerinin...
no-image-available

IPC-4556 - Amendment 1

Specification for Electroless Nickel/Electroless Palladium/Immersion Gold (ENEPIG) Plating for Printed Circuit Boards

Document #:
IPC-4556
Revision
Original Version
Product Type
Amendment
Released:  01/01/2016
Language
English
The Amendment 1 to IPC-4556 made the following changes to the base specification: a) It added the absolute value of the maximum thickness for the immersion gold of 0.070 μm [2.8 μin] that accompanies the statistically valid minimum immersion gold thickness; b) It added two more photomicrograph images to provide better information on identifying nickel hyper corrosion; c) It added the basis of...
no-image-available

IPC-4552 - Amendment 1

Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards

Document #:
IPC-4552
Revision
Original Version
Product Type
Amendment
Released:  06/12/2012
Language
English
Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards Amendment 1 to IPC-4552 replaces the Table 3-1 Requirements of Electroless Nickel Immersion Gold Plating plus also replaces all of sections 3.2.1 Immersion Nickel Thickness and 3.2.2 Immersion Gold Thickness in the original release of the IPC-4552. The Amendment 1 permits the use of thinner gold (≥4 µm...
no-image-available

IPC-4552 - Amendment 2

Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards

Document #:
IPC-4552
Revision
Original Version
Product Type
Amendment
Released:  09/01/2012
Language
English
Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards Amendment 2 to IPC-4552 is a new section in the original release of the IPC-4552. The Amendment 2 provides the “rules” by which any rework and/or repair of a printed board's ENIG surface finish is allowed. Effective September 2012.
no-image-available

IPC-A-610 - Revision F - Amendment 1

Acceptabilité des Assemblages Électroniques

Document #:
IPC-A-610
Revision
F
Product Type
Amendment
Released:  06/22/2017
Language
French
Ceci est un amendement à l’IPC-A-610-F, une norme reconnue selon un consensus industriel décrivant les exigences d’acceptabilité des assemblages électroniques. Les changements incluent, mais ne sont pas limités à, une révision des exigences de remplissage minimum des trous métallisés, des critères de vide pour les BGA à billes non affaissables et des critères de collage. Publiée en Décembre 2015
no-image-available

IPC-6012 - Revision D - Amendment 1

リジッドプリント板の認定および性能仕様-改定1

Document #:
IPC-6012
Revision
D
Product Type
Amendment
Released:  03/19/2019
Language
Japanese
本改訂は、IPC-6012Dで定められた銅ラップめっきの測定に関し、既存の許容基準に対し変更を加えるものである。本改訂は、新規設計品に施行される受け入れ要件の導入に伴い、旧来の設計品に追加的な品質認定作業を課すことのないよう、設計の有効日(2018年1月1日の前日まで、また、2018年1月1日以降)を基準に、クラス3製品の銅ラップめっきに二重基準を施行するものである。IPC-6012Dに記載する「銅ラップめっきの要求事項」の対象となる旧来の製品に対しては、本改訂は適用されない。8ページ。2019年1月翻訳。
no-image-available

IPC-A-610 - Revision F - Amendment 1

电子组件的可接受性 修订本1

Document #:
IPC-A-610
Revision
F
Product Type
Amendment
Released:  11/17/2016
Language
Chinese
该文件是IPC-A-610F的修订本，是电子组装可接受性要求的公认行业标准。变化包括，但不仅限于：镀通孔、最小填充要求、有非塌落焊料球的球栅阵列空洞标准和加固标准。
no-image-available

IPC-A-610 - Revision F - Amendment 1

Acceptabilitatea Ansamblurilor Electronice Amendament 1

Document #:
IPC-A-610
Revision
F
Product Type
Amendment
Released:  11/28/2016
Language
Romanian
Acesta este un amendament la standardul IPC-A-610F, un standard industrial recunoscut și adoptat, acoperind cerințe de acceptabilitate ale ansamblurilor electronice. Modificările includ, fără a se limita la acestea, o revizuire a cerințelor minime de umplere cu aliaj a găurilor metalizate, PTH, o schimbare a criteriilor pentru goluri la circuitele BGA cu bile fără turtire și cerințe noi pentru...
no-image-available

IPC/WHMA-A-620 - Revision B - Amendment 1

Requirements and Acceptance for Cable and Wire Harness Assemblies

Document #:
IPC/WHMA-A-620
Revision
B
Product Type
Amendment
Released:  11/07/2014
Language
Hebrew
Amendment 1 to IPC/WHMA-A-620B This amendment provides resolution to some internal conflicts, aligns common criteria to other IPC standards, and corrects some editorial errors. This amendment is only to be used in conjunction with IPC/WHMA-A-620 Revision B, October 2012. Follow your company policy and procedures to make pen and ink changes or notations to the published IPC/WHMA-A-620 Revision B...
1-24 of 24

Coming Soon

IPC-7095E: Design and Assembly Process Implementation for Ball Grid Arrays (BGAs)

IPC-2294: Design Standard for Printed Electronics on Rigid Substrates

IPC-6904: Qualification and Performance Specifications for Printed Electronics on Rigid Substrates

J-STD-005B: Requirements for Soldering Pastes

IPC-9691C: User Guide for the IPC-TM-650, Method 2.6.25 Conductive Anodic Filament (CAF) Resistance and Other Internal Electrochemical Migration Testing

IPC-4105: Specification for Metal Base Copper Clad laminates for Rigid Printed Boards

J-STD-609C: Marking and Labeling of Components, PCBs and PCBAs to Identify Lead (Pb), Lead-Free (Pb-free) and Other Attributes

IPC-4556A: Specification for Electroless Nickel/Electroless Palladium/ Immersion Gold (ENEPIG) Plating for Printed Boards

J-STD-004D: Requirements for Soldering Fluxes

IPC-4413: Specification for Finished Fabric Woven from Low Dk Glass for Printed Boards

IPC-HERMES-9852 Version 1.6: The Global Standard for Machine-to-Machine Communication in SMT Assembly