Your results
Document #
Language
Products
IPC-6012E-AM1 is an Amendent to the IPC-6012E that clarifes the distinction between receding and dewetting solder in reflowed SPb or HASL coatings. The Amendment also provides amended criteria for minimum external conductor thickness of the finished printed board and new acceptance criteria for the minimum thickness of internal plated layers
Amendment 1 to IPC-7711/21C, the document provides procedures for removal and installation of D-Pak components
IPC-4554, "Specification for Immersion Tin Plating for Printed Circuit Boards," is the third document in a series of specifications [the first two are: IPC-4552 which addresses electroless nickel/immersion gold (ENIG) and IPC-4553 which addresses immersion silver (IAg)] that set the requirements for printed circuit board surface finishes that are alternates to eutectic tin-lead. IPC-4554, a full...
IPC-6013D-AM1 is an amendment makes changes to the existing acceptance criteria for copper wrap plating measurements as defined by IPC-6013D. IPC-6013D-AM1 is an amendment which implements a dual criterion for Class 3 copper wrap plating, based on design effectivity (before and after July 01, 2018), so as not to impose onto legacy designs any additional qualification activity associated with...
IPC/JEDEC-9707-AM1 is an amendment which clarifies that the standard is only applicable to transient bending during short-term test operations. The standard specifies a common method of establishing strain limits of board-level device interconnects under spherical transient bending conditions, the worst-case flexure condition that can occur during conventional printed board/system assembly...
The IPC-6012D-AM1 makes changes to the existing acceptance criteria for copper wrap plating measurements as defined by IPC-6012D. The IPC-6012D-AM1 implements a dual criterion for Class 3 copper wrap plating, based on design effectivity (before and after January 01, 2018), so as not to impose onto legacy designs any additional qualification activity associated with adopting acceptance requirements...
IPC-9252A Amendment 1, published in October 2012, provides clarification to requirements for resistive isolation testing, as well as the testing of accessible midpoints for resistive continuity testing.
IPC-6012E-AM1是IPC-6012E的修订本,澄清了再流焊SnPb或HASL镀层中退润湿和焊料回缩之间的区别。 该修订本还为成品印制板的最小外部导体厚度提供了修订标准,并为内部电镀层的最小厚度提供了新的接受标准。
Bu döküman; kaplı delikiçine sahip olan veya olmayan tek yüzlü, çift yüzlü baskı devre kartları ve kör/gömülü geçiş deliklerine sahip olan veya olmayan çok katmanlı baskı devre kartları ile metal çekirdekli kartları içeren sert baskı devre kartlarının kalifikasyonunu ve performansını kapsamaktadır. Son kaplama ve yüzey kaplama gereklilikleri, iletkenler, delikler/geçiş delikleri, kabul testlerinin...
Enmienda 1 al IPC-7711/21C, el documento proporciona los procedimientos para la extracción y la instalación de componentes D-Pak.
Ergänzung 1 zu IPC-7711/21C-DE, das Dokument enthält Verfahren für das Entfernen und Montieren von D-Pak-Komponenten.
The Amendment 1 to IPC-4556 made the following changes to the base specification: a) It added the absolute value of the maximum thickness for the immersion gold of 0.070 μm [2.8 μin] that accompanies the statistically valid minimum immersion gold thickness; b) It added two more photomicrograph images to provide better information on identifying nickel hyper corrosion; c) It added the basis of...
Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards Amendment 1 to IPC-4552 replaces the Table 3-1 Requirements of Electroless Nickel Immersion Gold Plating plus also replaces all of sections 3.2.1 Immersion Nickel Thickness and 3.2.2 Immersion Gold Thickness in the original release of the IPC-4552. The Amendment 1 permits the use of thinner gold (≥4 µm...
Specification for Electroless Nickel/Immersion Gold (ENIG) Plating for Printed Circuit Boards Amendment 2 to IPC-4552 is a new section in the original release of the IPC-4552. The Amendment 2 provides the “rules” by which any rework and/or repair of a printed board's ENIG surface finish is allowed. Effective September 2012.
Coming Soon
IPC-7095E: Design and Assembly Process Implementation for Ball Grid Arrays (BGAs)
IPC-7530B: Guidelines for Temperature Profiling for Mass Soldering Processes (Reflow & Wave)
IPC-2294: Design Standard for Printed Electronics on Rigid Substrates
IPC-6904: Qualification and Performance Specifications for Printed Electronics on Rigid Substrates
IPC-4105: Specification for Metal Base Copper Clad laminates for Rigid Printed Boards