Products
IPC-4101E covers the requirements for base materials that are referred to as laminate or prepreg and listed in the specification sheets that are contained in the last of the main body. These are to be used primarily for rigid and multilayer printed boards for electronic interconnections. This document contains 65 individual specification sheets that can be searched using keywords. These keywords...
IPC JEDEC J-STD-020 is used to determine what moisture-sensitivity-level (MSL) classification level should be used so that surface mount devices (SMDs) can be properly packaged, stored and handled to avoid subsequent thermal and mechanical damage during the assembly solder reflow attachment and/or repair operation. J-STD-020 covers components to be processed at higher temperatures for lead-free...
This redline provides a side-by-side comparison the changes from Revision C to Revision D of IPC-7711/21.
Contains over 150 industry approved test techniques and procedures for chemical, mechanical, electrical, and environmental tests on all forms of printed boards and connectors. New and updated test methods are available for download at https://www.ipc.org/test-methods.
Covers the various conductive and dielectric materials that can be used for the fabrication of HDI and microvias. The 23 specification sheets included in IPC/JPCA-4104 cover the qualification and conformance requirements for such materials as photoimageable dielectric dry films and liquids, epoxy blends and coated foils. IPC/JPCA-4104 also includes six new test methods developed specifically for...
This document covers requirements and test methods for anisotropically conductive adhesive films used to bond and electrically connect components. Applications include the following: flexible PWB-to-glass, flexible PWB-to-rigid PWB, flip chip-to-glass, flip chip-to-flexible PWB, flip chip-to-rigid PWB, and fine pitch SMD. The adhesive film may be supplied pre-attached to a flexible circuit or...
IPC-3406 offers guidelines for selecting electrically conductive adhesives for use in electronics manufacturing as solder alternatives. The process discussion attempts to stay within the bounds of the existing solder assembly infrastructure. Both major types of adhesives, isotropic (conducting equally in all directions) and anisotropic (unidirectional conductivity) are covered. Polymer adhesives...
This standard establishes construction detail requirements for bumps and other terminal structures used for Flip Chip Scale carriers. The specific standards for different terminations are appropriately matched to a particular interconnection process and include such diverse terminations as solder bumps, columns, non-melting stand-offs and conductive polymer deposits. The document articulates a set...
The Joint Industry Guide Material Composition Declaration for Electrotechnical Products has been updated to include the most recent substances for restriction. The JIG-101 is an industry materials declaration guide that facilitates reporting of material content information across the global electrotechnical supply chain. This document sets minimum requirements for a materials declaration. The...
IPC-9191 reflects the principals of statistical process control (SPC) represented by ISO/DIS 11462-1, Guidelines for Implementation of Statistical Process Control (SPC) -- Part 1: Elements of SPC. This document outlines the SPC philosophy, implementation strategies, tools, and techniques used for relating process control and capability to final product requirements. Supersedes IPC-PC-90.
The industry's first specification for the evaluation of a legend and/or marking ink material for the determination of acceptability of use in a standard printed board system. IPC-4781 provides coverage for adhesion, material qualification and testing, resistances to solvents, requirements for resistance to lead-free solders, and electrical requirements. 17 pages. Released May 2008.
Covers requirements and test methods for thermally conductive dielectric adhesives used to bond components in place. Permanent, removable and self-shimming adhesives are addressed. 18 pages. Released January 1995.
This document describes materials that can be used for the fabrication of embedded passive resistor devices within the finished printed circuit board substrate. It provides information on general designations and associated characteristics of embedded passive device (EPD) resistor materials. The document shall be used as a qualification and conformance standard for designers and users when...
IPC-4413 standard covers finished fabrics woven from low Dk electrical grade glass fiber yarns that are intended as a reinforcing material in laminated plastics for electrical and electronic use. All fabrics covered by IPC-4413 standard are plain weave.
Establishes design concepts, guidelines and procedures for reliable printed wiring assemblies. Focuses on SMT or mixed technology PWAs, specifically addressing the interconnect structure and the solder joint itself. Discusses substrates, components, attachment materials, coatings and assembly processes and testing considerations. In addition, this document contains detailed appendices covering...
This voluntary standard establishes minimum requirements for the design, installation, operation and maintenance of electrically heated process equipment in order to minimize electrical hazards and prevent fires that may occur in combustible tanks, tank liners and drying equipment.
Printed board flatness is largely affected by a change in intrinsic properties through exposure to variances in temperature. The worst case deviation of the printed board from flatness may be at room temperature, peak temperature during reflow, or at any temperature in between. Printed board flatness must therefore be characterized during the entire reflow thermal cycle, and not solely at room...
IPC-4101D-WAM1 covers the requirements for base materials that are referred to as laminate or prepreg. These are to be used primarily for rigid and multilayer printed boards for electrical and electronic circuits. This document contains 65 individual specification sheets that can be searched using keywords. These keywords allow the document's user to find materials of a similar nature, but with...
This specification covers the requirements for base materials that are referred to as laminate or prepreg. These are to be used primarily for rigid and multilayer printed boards for electrical and electronic circuits. This document contains 64 individual specification sheets that can be searched using keywords. These keywords allow the document's user to find materials of a similar nature, but...
This standard prescribes test methods, defect definitions, acceptance criteria, and illustrations for assessing the solderability of electronic component leads, terminations, solid wires, stranded wires, lugs and tabs. A test method for the resistance to dissolution/dewetting of metallization is also included in the standard. Intended for use by both vendors and users, J-STD-002D was developed by...
The European Union’s Restriction of Hazardous Substances (RoHS) legislation has had a profound impact on the electronics industry. One of the restricted substances, lead (Pb), is commonly used in alloys with tin for component finishes, printed board finishes and solders. Pb-free materials directly affect product performance, reliability and service life in many ways. There have been numerous...
This guideline standard is intended to aid in interpretation of the requirements in IPC-9191, "General Guidelines for Implementation of Statistical process Control," specifically for printed board assembly (PBA) manufacture. This document and IPC-9191 should be used together; the standards are cross-referenced to each other in the Appendices of this guideline. This standard promotes process...
This standard identifies the moisture sensitivity classification level of passive surface mount devices and through-hole components, subjected to reflow soldering, so that they can be properly packaged, stored, and handled to avoid subsequent thermal/mechanical damage during assembly solder reflow attachment and/or repair operation. This standard may be used to determine what classification level...
This document standardizes the performance parameters for air moving devices. The phrase "air moving device" (or "air mover") refers to equipment such as, fans, blowers and other forced air movement technologies. These air moving devices are used in the electronics industry for the cooling of heat-producing components, and range from small devices mounted directly to hot components such as...
This document is a tool for a customer or supplier organization's internal audit group to assess a statistical process control (SPC) system against the requirements of IPC-9191. This document should be used by customers and suppliers of any size and for any commodity. This tool can be used to perform an assessment of the use of SPC at both organizational and process levels. The questions in this...
Coming Soon
IPC-7095E: Design and Assembly Process Implementation for Ball Grid Arrays (BGAs)
IPC-7530B: Guidelines for Temperature Profiling for Mass Soldering Processes (Reflow & Wave)
IPC-2294: Design Standard for Printed Electronics on Rigid Substrates
IPC-6904: Qualification and Performance Specifications for Printed Electronics on Rigid Substrates
IPC-4105: Specification for Metal Base Copper Clad laminates for Rigid Printed Boards